Search Results

Air flow around a car front end configuration and through the radiator and condenser was computed simultaneously. Although the engine compartment was simplified to reduce computational cost, comparison of experimental data with the analysis showed excellent prediction of the air flow through the radiator and condenser.

The colour painting of polypropylene bumpers has required development of a new polypropylene surface treatment which provides improved adhesion of the paint film to polypropylene. According to the results of various improvement studies on the application of plasma treatment, it has been discovered that surface treatment by means of plasma of an oxygen and nitrogen gas mixture activated by microwave (2,450 MHz) provides a remarkable improvement in adhesion. Furthermore, establishing a technique to diffuse plasma effectively within the treatment chamber has enabled a uniform surface treatment of several polypropylene bumpers formed in large and complicated shapes.

Authors have developed an apparatus which measures the piston temperature using electromagnetic induction. The characteristics of this apparatus are as follows; 1 Applicable to 6 points per cylinder and all cylinders 2 Capable of measuring while the engine is running from start to 6000r/min full-load operation 3 Wide measuring range; from -30 to 400 °C 4 High accuracy; ±2.5 °C 5 Quick and easy setup 6 High durability This technology contributes to realizing the best balance of piston reliability and matching of combustion conditions. In this report, authors analyzed its influences upon piston temperature when the ignition timing,the oil/water temperature or the oil flow from piston jet were changed, respectively.

ϵ-caprolactam was polymerized in the interlayer space of montmorillonite, the clay mineral yielding a nylon-clay hybrid (NCH). X-ray and TEM measurements revealed that each template of the silicate, which was 1 nm thick, was dispersed in the nylon 6 matrix, and that the interlayer distance of clay increased continuously from 1.2 nm for the unintercalated material to 21.4 nm for the intercalated material. Thus, NCH is a polymer-based molecular composite or a nano-composite. NCH contains 1-15 vol% of monolayer clay. Injection-molded NCH showed excellent mechanical properties compared with nylon 6 in terms of tensile strength, tensile modulus and heat resistance. The tensile modulus of NCH was twice that of Nylon 6, and the heat distortion temperature increased from 65°C for nylon 6 to 145°C for the NCH containing only 1.6 vol% of a clay mineral. It was found that such excellent properties of an NCH system was due to the strong ionic interaction between nylon 6 and the silicate layer.

This paper describes a new plastic coloring and forming system. The system greatly reduces the time and amount of raw materials necessary for color changes, and eliminates the need for manual cleaning during a color change. This system is well-suited for small-lot production with frequent color changes, as well as for automated production systems. The system is being used by auto parts makers, and is practical in a variety of other fields involved with the coloring and forming of plastics.

A method of fatigue life estimation for the spot-welds of vehicle body structures by means of Finite Element Analysis (FEA) was studied. 6 general forces applied to a nugget of spot-weld under multiaxial loads were determined and the Nominal Structural Stress (σns) was calculated from them. It was confirmed that fatigue strength of the spot-welds under various multiaxial loads could be estimated universally by using σns. Based on the theory of elasticity of plates, stress of spot-weld nugget was analyzed. The theoretical equations for determining the principal stress at the nugget edge from6 general forces acting on a nugget were derived. And the principal stress was defined as the σns. The value of σns was determined by FEM that used a solid model and compared with the theoretical calculation value. They agreed quite well. Fatigue tests of DC specimens under various multiaxial loads (shear plus cross tension and tensile shear plus torsion) were conducted.

A system to measure transient temperature distribution on the brake disc rotor at high speed braking has been developed and its measuring principle and configuration were discussed in this paper. This system consists of two revolution sensors and two sets of optical fiber array, photoelectric elements, and microprocessor, which fiber array is so arranged that it faces the brake disc rotor. This new system has the following features: (1) Measuring is made using a visible radiation wavelength range for red hot temperatures higher than 550°C.

Conventionally, sound insulation materials have been applied to control interior noise above 500 Hz, and damping materials to control interior noise below 500 Hz. In this paper, the noise control component for vehicle panels, which consists of damping material and sound insulation material, is investigated by using a two-degrees-of-freedom system. The investigation shows that sound insulation material can be effective in reducing interior noise below 500 Hz if its stiffness is reduced. This stiffness depends not only on the spring of the material itself but also on its pneumatic spring which is determined by air-flow resistance. This paper concludes with applications of techniques to reduce interior noise below 500 Hz by improving sound insulation materials.

As a means of effectively incorporating the concept of “life cycle” for reducing the environmental impact of the automobile, we carried out a life cycle inventory study on a part-by-part basis. The targets of our study are the fuel tanks that are made of different materials and manufacturing processes. One is made of steel, and the other is made of plastic, both perform identical functions. Our evaluation study encompasses the period from the manufacturing of the main materials until the disposal of the tanks. The evaluation items consist of the amount of energy consumed and the emissions (of CO2, NOx, SOx, and PM) that are released into the atmosphere. The results show that the plastic tank poses a greater burden in terms of the amount of energy consumed and the CO2 and NOx emitted.

This paper analyzes the vibration of open-top cars known as lateral shake. The characteristics of the phenomenon were identified by means of road tests and a test method called the shake test was devised to reproduce these characteristics in order that the respective roles of the suspension, body and engine could be determined. On the basis of the analysis findings, a simple but practical simulation model was realized and used to investigate various methods of reducing lateral shake. The simulations indicated that although changing the natural frequency of the suspension has little effect, increasing the natural torsional frequency of the body and/or utilizing the engine as a dynamic damper results in a significant improvement. Further experiments conclusively demonstrated that by optimizing the body structure in accordance with FEM analysis results and optimizing the spring constant of the engine mounts, the level of lateral shake can be halved.

The behavior of spray injections to turbulent duct flows from a slit injector for direct-injection gasoline engines was investigated using a combination of large eddy simulation (LES) and Lagrangian discrete droplet model (DDM). As a result, diffusion of droplets in stronger turbulent flows was observed at a later stage of the injection. Moreover, we compared calculation and experimental results by generating a pseudo-particle image from the calculation result.

Automobile production technology has been transferred in the order of "automobile assembly technology", "automotive parts manufacturing technology" and "production preparation technology". Transfer of our "automobile assembly technology" has already been nearly 100% completed and, as the manufacture of local parts is promoted and our experiences to undergo model changes are widened, the transfer of "automotive parts manufacturing technology" and "production preparation technology" is making a steady progress. The most critical point that makes the technical transfer difficult is the small automobile markets in developing countries where it is impossible to acquire a sufficient production volume which permits satisfactorily low cost. Various measures to secure a sufficient production volume such as exports and complementation within regions have been taken so far, but any remarkable effect has not been achieved.

The characteristic of In-Cylinder gas motion of a multivalve engine is compared with a single intake valve engine, which have been predicted by a three-dimensional numerical simulation and flow visualization. The measured intake valve outlet velocity from helical and straight port was adopted as the boundary conditions. The computer graphics technique has been utilized to express the predicted numerical results as moving picture like visualized flow. This flow pattern was compared with the actual flow pattern visualized with metaldehyde as the tracer using the bottom viewed engine, which showed good agreement. The prediction for the multivalve engine showed that the swirl velocity is rapidly reduced by interaction between the flows from the two port, but the turbulence kinetic energy is similar to that in the engines with a single intake valve with helical port.

In contrast to the sensory inspection conventionally performed on the firing bench during final assembly, a technology in which quality inspections are distributed throughout the engine assembly line by using an electric motor to drive the engine, has been developed. Through this process, combustion conditions can be quantitatively tested by component, and leak test conditions can be optimized. Consequently, defects can be detected and their causes identified at an early stage of assembly, thus accelerating the feedback of information to the appropriate process. The result, a level of product quality that is higher than through the conventional means.

The authors developed a high-reliability low-cost gold-plated connector for automobiles. The connector is covered with three plated layers, nickel, palladium-nickel alloy, and gold. The three-layer plating helps to reduce the required thickness of gold. This paper describes the reasons why palladium-nickel plating was adopted and compares the corrosion resistance, oxidation resistance and wear resistance of three-layer-plated materials with those of conventional gold-plated materials. In addition, the characterisitics of three-layer-plated connectors were compared with those of conventional gold-plated connectors. It was found that the reliability of three-layer-plated connectors was as high as that of conventional gold-plated connectors.

Engine friction reduction is an effective means to improve fuel consumption. Fluid friction reduction of main bearing is examined for engine friction reduction in cold condition. As one of the examinations, it was focused on low temperature of lubricating oil in the early stage during engine cold start. In hydrodynamic lubrication, the oil film temperature is maintained by balance between heat generation and heat transfer. The heat generation is generated by shear of lubricating oil. The factors of the heat transfer, the following elements are considered as follows, A) The heat transfer to a crank shaft, B) The heat transfer to a bearing, C) The heat transfer by convection. If the heat generation is constant, oil film temperature is increased by reduction of heat transfer. It is considered that the reduction of oil leakage and reduction of the heat transfer by convection is equivalent.

In order to achieve higher assembly accuracy for automotive body, increased body rigidity, and decreased stamping and assembly costs in car body manufacturing, a new method of sheet metal stamping has been developed, in which several blanks of different strength and thickness are integrated using CO2 laser-welding. The stamping formability of the laser-welded blank is limited compared with that of the conventional single blank. It is very difficult to predict the exact decrease in formability for different positions of the weld line and for different matching of materials. Because experimental estimations were indispensable for stamping die designers to evaluate formability at the stage of planning dies, many man-hours were spent conducting actual experiments.

Previous studies and recent practical aerodynamic evaluations have shown that aerodynamic drag of passenger vehicles with “ground simulation” with moving ground and rotating wheels may increase in some cases and decrease in other cases relative to the fixed ground and stationary wheel conditions. Accordingly, the effects of the ground simulation on the aerodynamic drag should be deeply understood for further drag reduction. Although the previous studies demonstrated what is changed by the ground simulation, the reason for the change has not been fully understood. In this article, the effects of wheels and wheel houses attachment and those by the ground simulation with ground movement and wheel rotation on the aerodynamic drag were investigated by quantification of the underfloor flow that plays a crucially important role on the formation of vortical structure around vehicles.

Certain dimensional factors and a method for evaluating dimensional errors have been developed to improve the service life of the Rzeppa universal joint. The Rzeppa joint Spalling life is extended by disposition of the balls on a constant velocity plane under loading conditions which include proper determination of the offsets of the ball grooves and the windows of the cage. The ball center containment ranges, which consist of the grooves of both inner and outer races, can be affected by dimensional miscalculation of components. Moreover, the extent of scatter in the ball center containment ranges has a remarkable effect on the Rzeppa joint service life.

To reduse crosswind sensitivity, the yaw moment should be decreased under both transient and steady conditions. The transient condition is when a vehicle comes out immediately from a tunnel into a crosswind while the steady condition is when driving straight along the coastline. After studying the pressure distribution and the flow pattern around the body, we have reached the ideal air flow at the front-side corner that reduces the yaw moment under both conditions. And we have devised an entirely new method to achieve this better air flow. The method uses an internal flow generated by a pressure difference in the flow feeld to create a jet effect and by using only a duct for internal flow to control the outside air flow. It is done without any change to the exterior styling, except at the flow exit. We call it “Aero Slit”. This “Aero Slit” is effective only under crosswind conditions, and does not increase aerodynamic drag when a crosswind is not blowing.